Tel No. (+86) 371-55629010

15mv coal fired hot water boiler vietnam in building materials industry

First, we need to clear in the boiler "coal to gas" process, to determine the different rehabilitation programs depending on the furnace. Second, grasp the "coal to gas," the key link. 1, removal of the original coal-fired boiler slag machine, coal hopper, coal equipment, chain grate, gearbox and so on. 2, by calculating the heat transfer in the furnace, the furnace geometry is determined, the center position of the furnace flame. Re-casting furnace, furnace refractory concrete casting material used, a large ratio of aggregate: Aggregate: Small aggregate: Sand: = 4:2:1:1:2 refractory cement. After the boiler pipe arch to avoid the flame center position, after the original arch pipe elevation on the basis of the original slope. 3, installation of explosion-proof doors. For gas-fired boiler, the blast doors is an important facility to protect the safe operation of the boiler. 4, boiler water test of 1.25 times the working pressure. Third, no matter what kind of furnace should be noted that in the transformation of the construction of the following questions: 1, should guarantee the smooth flow of flue gas, have a good fullness and should avoid dead ends and dead. 2, the burner should be provided at the height position of the center of the furnace, and the combustion space and has sufficient length. Flame should not be flushed to the wall heating surface, so as to avoid incomplete combustion gases local overheating and damage to the wall. 3, since the combustion gas in the furnace backlash, high thermal strength, exposed to the bottom of the drum in the furnace should be adiabatic process. 4, various pipes, fire tube boiler furnace wall substantially refractory brick masonry, and shield plus insulation material. In the "coal to gas" should pay attention to the tightness of the furnace wall, minimizing the original door, door checks, etc., can assemble the refractory block, prevent cold air flames wounding or excessive leakage into the furnace , affecting boiler efficiency, to see the fire hole must remain closed also should see the fire hole, heat-resistant glass viewing by fire. 5, the furnace boiler and gas than coal-fired boilers, is generally greater, there is sufficient combustion space, increase the volume of gas, does not affect the transformation of combustion conditions. If the user requests output significantly improved boiler, the furnace can be increased radiation heating surface, to remove scale and soot while the inner surface of the outer heating of the original, so that without increasing the volume of the boiler case to improve the boiler output is not a problem. Thermodynamic calculations must do in the boiler, while the smoke but also good wind resistance calculation intensity calculation. Fourth, the correct choice of matching burner

Fangkuai Boiler is based on low-nitrogen energy-saving and environmental protection. It focuses on the development trend and uses universal excellent technology, products and services. According to such a method, it is now applicable to the development of society around the world, promotes cutting-edge work in the future manufacturing industry, and maintains the ideal use of customers in various industries.

Exhaust gas temperature factors affect the efficiency of the boiler 1. High boilers (1) ring-shaped heating surface. A protective pot operation due to the heated area ash causing poor heat transfer. Secondly heating surface by erosion wear of the high temperature flue gas, resulting in good convection bank vent for taking soil pipe powder blocking manner with less number F, powder powder increases the number of block f will inevitably result in decreased heat transfer effect of the heating surface, the deterioration of the operating parameters. such that the exhaust gas temperature medium (2) bits leakage furnace, the burner burning roll. Wind refuse mud furnace, burner combustion burning material will travel in incomplete protection technology, resulting in frameshift flame, which led to the degree of BU smoke Mi (3) poor operating conditions. A secondary air must have appropriate warehouse Shan ratio during burning. Secondary air Diao large ring-shaped hold burning effect, will affect the wind. Powder mix. 2. boiler water quality factors is an important indicator of pot care, but also a very appropriate to link, the water quality directly affects the safe and economical operation of boiler protection, internal cleaning of the heating surface of each pier can add endothermic t, It will increase the efficiency of the care of the pot. Shanghai each newly installed boiler heating surfaces are clean, the indicators are good, heat transfer efficiency is higher. But with longer run time, the inside of the tube or bi or furring rights corrosion, resulting in decreased heat transfer efficiency, pot nursing efficiency drops, after scaling or corrosion deterioration. Pot can also cause over-temperature protection wall even Los iron . 3. mechanical incomplete Tanzania Heat loss if the twist burner for burning Yan basin, coal dust mixed into the retaining find not carried out, resulting in insufficient fuel you burn. Shan increase mechanical incomplete burning loss. On the other hand due to air leakage protection Mu. Mi will lead to reduced care. Shan burn rate of decline. Powder fire longer, is not conducive to coal combustion rate, resulting in an incomplete tender burn solid increase in losses. Division personnel to operate the operation level of the level 4. 0 operator is not high, not be reasonably performed with the wind, the rotation speed control discharge protection, timely cleaning, descaling, resulting worthy material is not completely burned proud. Long low thermal efficiency in the actual operation, often occurs due to the experience of the operating personnel, resulting in decreased operating efficiency of the unit, adjust the low level of security decline. 'On the other hand, there is a difference operator P forced cultural quality and the level of practical skills.

Why choose ZG as biomass fired water tube boiler manufacturer

ZG Boiler offers Biomass water tube boiler systems for all applications. The wide variety of our product ranges successfully serve the different need of our customers and help them to increase efficiency and reduce energy cost. Considering the abundant of natural energy resources such as coal, biomass, rice husk, wood chips and others, which are available in the Southeast Asia region, ZG Boiler has developed the intelligent boiler systems that fit to the local requirements and yet provide high efficiency, energy saving, safe and environmental friendly.