Fangkuai Company has a fully-automatic PLC intelligent control system designed and developed by itself with complete intellectual property rights. It adopts a combination of mechatronic control equipment and a programmable logic controller (PLC). Take the advanced programmable logic controller (PLC) as the "central processing unit" of the control system. The control system is operated through the touch screen, which greatly improves the degree of automatic control and operation reliability of the manufacturing companies boiler 10t, and the operation is simpler and more intuitive.
Nowadays, the use of gas-fired steam boiler has become more and more frequent, and the boilers all over the country have changed the use of gas-fired boiler with each passing day. Although the domestic professional gas-fired steam boiler is stable in operation and less energy-saving and consumption-reducing in sewage discharge, it is necessary to use proper maintenance in the case of long-term non-use in order to carry out normal use. Specific gas-fired steam boiler maintenance methods in the case of not in use and see below for detailed analysis of the following:
1: dry maintenance of gas-fired steam boilers should remove the boiler water after shutdown, and then thoroughly remove and rinse the dirt from the interior. And keep the oven dry so as not to be seduced. You can dry the chamber with a light fire, but not with a fire. Also be careful to close all hand-hole piping valves and place the quicklime tray in the drum. Check the boiler at least three months without using a gas-fired steam boiler for a long time. If the quicklime in the chamber is crushed into powder, the new lime needs to be replaced immediately to ensure that the drying protection in the furnace of the gas steam cooker is not corroded by moisture.
2: in addition to dry maintenance, wet maintenance of gas-fired steam boilers can also be done by means of wet maintenance, which is to remove internal dirt after discharging the water in the furnace, and to fill the chamber with treated water and then heat it to the required temperature. The gas in the water is then discharged out of the furnace and all valves are closed. In this way, the furnace is filled with water to complete maintenance. Of course, wet maintenance should not be used in cold weather to prevent water icing and damage to the tank. It can be seen that the gas-fired steam boiler in the case of not in use is mainly dry and wet method of maintenance, which kind of specific use Maintenance method according to different site and climate conditions to make flexible choice.
Characteristics of a gas-fired commercial fast ultra-low nitrogen emissions party commercial gas manufacturing companies boiler 10t number of advanced processing techniques, such as the premix, and the like of FGR combustion flue gas recirculation techniques, by low nitrogen from different locations, oxynitride matter emission amount can be as low as 20 mg / m or less, air pollution fully meet the most stringent emission requirements of areas (30 mg / cubic). Second, ultra-high thermal efficiency thermal efficiency of the boiler is determined to run into one of the main factors of cost, generally speaking, the higher the thermal efficiency of the boiler run more provincial gas money. Fast side boiler thermal efficiency study never stopped, by using a commercial gas boiler finned tubes, pipes wings (fast independent patent square) elements, such as efficient heat transfer, combined condensate recovery technology can achieve high thermal efficiency of 108%. Third, peace of mind secure and reliable way to quickly set up a number of boiler safety facilities, such as temperature protection, pressure protection, burner protection, power protection, etc., remote monitoring system run time online monitoring boiler, early warning of dangerous situations. Can reduce the labor burden fireman who, in turn boiler full range of protected. Fourth, the modular design of the boiler can also be a single use more than one joint control operation, when the demand for hot water is high school, you can start jointly running multiple boilers, and if the school is not so demand for hot water when high, you can choose to start single boiler. This design structure effectively solve the school change in the demand for hot water problems in different seasons, with a flexible, avoid waste of resources phenomena.
The manufacturing companies boiler 10t brand problem must also be felt by many people, that is, the well-branded boiler often performs more reliably in its technical consultation, product protection and after-sales service, and so on. Therefore, which gas boiler brand is good in selecting the relevant equipment should first consider the issue, and this can be generally through the online access to the gas boiler brand ranked information reasonable evaluation.