Tel No. (+86) 371-55629010

4 ton coal hot water boiler

Combustion characteristics and operation of steam boiler steam for steam boilers everyone know how much will the following to let everyone have a preliminary understanding of the steam boiler by two aspects, but also hope to give a friend wanted to buy a steam boiler of some help. Chain-type layer is generally fixed combustible fuel steam boiler chain grate or a grate (the traveling), it is fixed only for small coal-fired boilers. The most commonly used medium-sized coal-fired boilers or for chain grate, as the chain travels will gradually sent to the tail of the coal grate in the process of moving complete fuel combustion tube from the inlet to the lower part of the grate grate internal supplemental air required for combustion, ignition top-down, no ventilation grate uneven seam and around the relative movement, through non-flammable. After heating area of ​​the heating flue gas temperature of the working fluid designed to flow through the same furnace hot flue gas and heating surface arranged in the other exhaust flue boiler. Incidental chain grate type, scale type, beams, and other means, the current domestic applications mainly for small and medium-sized joint type and scale type chain grate, generally large chain grate beam type. Former steam boiler steam boiler system to start all waterproof steam cylinder valve open, let go condensate. The inlet steam valve slightly open, to warm up the cylinder, drain cocks to be out after closing the steam, drain cocks. The steam valve was then opened progressively larger until drainage tank vent cock and water out there, and closed vent cock drain cocks. Turn on the water supply valve to the boiler feed water. Steam boiler in operation if there is gas in timely attention tank, water tank periodically open the air discharge valve, in order to avoid air resistance tank, the influent. Pump flow regulator bypass should be adjusted to achieve the degree of opening of the valve, and not with a method of adjusting the outlet valve is adjusted. At the rated discharge pressure of the pump, which inlet pressure should not exceed a predetermined value. Inlet and exhaust pressure difference should be maintained within a predetermined range. Steam boiler steam valve should be shut down first, then turn off the water valve and turn on the water valve is open, then turn on the water faucet open the lower part of the tank and cylinder, the cylinder water drain. Of steam cylinder reciprocating pump, which cylinder two stroke difference should not exceed 5% of rated travel.

Greater than 65t / h industrial boiler of what air pollutant emission standards should be executed? A: The State Environmental Protection Administration, Central Division-standard [1993] No. 012 document pointed out that the emergence of a small number of parameters currently higher than GB1921-80 "industrial steam boiler parameters Series" and GB3166-82 "4 ton coal hot water boiler parameters Series" layer burning, stoker boiler, regardless of its use Zanan GB1327-91 execution. Therefore> 65t / h or more (except coal, circulating fluidized bed, and fuel, gas fired boilers) industrial boilers should be performed "boiler air pollutant emission standards."

Gas Steam Boiler non-normal stall, a phenomenon and treatment, flame reasons: 1, the operation of the auxiliary power supply or trip interruption. 2, boiler combustion instability. 3, the load is too low, so that the load sharply mill automatic ignition energy loss or failure of combustion. 4, mutant coal, coal volatile or low calorific value. 5, the automatic combustion flame detector failure or failure caused by tripping mill. 6, or blast furnace wall tubes serious improper boiler soot-blowing operation, a large amount of water vapor into the combustion chamber. 7, coal pulverizing system, fuel system failure, resulting in a significant amount of fuel reduction or interruption. Or with a large amount of water in the fuel oil gun blocked too many impurities, low pressure steam or atomized. Second, the phenomenon: 1, a significant increase in furnace pressure, furnace flame monitoring flameless CRT display. See the fire no fire hole, BTG warning window MFT warning lights. 2, the unit load decrease, the steam flow drops rapidly, each segment working medium temperature, the vapor pressure decreases, the value of oxygen surge. Third, the method of treatment: 1, if the MFT tripping protection, should an emergency shutdown processing, stop the supply of fuel. 2, identify the cause flameout, and try to eliminate, to conduct a comprehensive inspection of the boiler, after confirming the device properly, can restart. How early circulating fluidized bed boiler ignition achieve the protection of reheaters? Fire causes of valve failure chemical industry regulation and Countermeasures bearing parts heat treated high boiler common defects due to low bypass the security gate and reheaters failure phenomenon and treatment of condensate pump turbine worm gear failure cause analysis and improvement measures in the pneumatic valve powder operating system instructions on how to implement.

Our other fast boiler in the boiler industry strength already heard, through cooperation proves that our choice is correct. This water-tube boilers installed very quickly, basically no delay our production process, bring benefits to the enterprise. --customer feedback