As a global boiler agua quente a enterprise, Fangkuai Boiler attaches great importance to the opportunity of communication with customers. Therefore, we have set up a sales team of more than 100 people to visit customer units regularly to check the boiler operation status. Not only can timely search the customer's use feedback and boiler improvement opinions, provide a clearer development direction for equipment research and development, but also assist users in the testing and commissioning of boilers and maintenance work, full life cycle services, and solve customer cooperation projects. The problem is that nobody cares ".
1. Furnace and the two sides of burner zone adopts membrane water-cooled furnace structure. The membrane structure of wood fired steam boiler, our company’s solely design once used in electric boiler , is now applied in shaped assemble boiler. Its advantages lie in great thermal transmission heat, better heat transfer effect, lower heat loss ,better air impermeability, no wall distortion and no ash leakage.
2. The structure of arches adopts the newest technology --the upside”a” technology, which is awarded the national science and technology prize. The front arch is high and short while the back arch is low and long. And the part near the exit is inverse inclined type,while the front arch is 45ºinclined type, they together form a downside a flame structure,which makes the lean coal combustion easier and it can adjust itself to a wide rang of coal types. In this way, the flue gas is kept within the furnace a longer time, and the combustion efficiency is higher. The streamline shaped back arch can throw the non-burned carbon grains in the middle and back part of furnace to the front, so that the coal can be easier to be ignited and the ignition lines are tide.
3. The wood fired steam boiler adopts double layers or single layer layout structure, which can meet the customers’ requirements better.
Henan boiler agua quente a manufacturers fuel gas combustion boiler features a contrast, combustion of fuel is a liquid fuel and fuel oil, its boiling point is always lower than the ignition point, so that fuel combustion is always performed in the gaseous state. Fuel oil particles atomized by the jet into the furnace after the furnace is heated by high temperature flue gas, gasification, and hydrocarbon ambient air encounters the oxygen gasification, a flame. Heat produced by combustion of oil particles pass a part of the gasification and combustion of oil particles continuously, until the burning ember. The smaller the diameter of oil particles, the faster the combustion of oil particles. Similarly, the oxygen required for combustion of oil particles can be supplied in time, the combustion of oil particles can more quickly. Therefore enhanced combustion of oil must do the following: 1, to improve quality of atomization, the oil particle diameter is reduced; 2, increasing the relative velocity of the air and oil particles; 3, reasonable air distribution. Second, the combustion gas boiler manufacturers Laid Henan boiler ignition gas with a high calorific value, large amount of air, can make the combustion gas, a large amount of air mixed therewith. No fuel combustion gas atomization process with the gasification process. Gas and air mixing mode, the flame length and flame temperature has a significant impact on the intensity of the combustion. Depending on the mixed mode, the combustion method of the boiler manufacturer Henan gas boiler can be divided into three types: 1, i.e., this method does not pre-mixed combustion diffusion combustion, but interdiffusion gas nozzle opening, and burned. Shao Shao stability advantages, the structure of appliance is simple, but the flame is longer, easy to produce incomplete combustion and carbonization of the heated area. 2, partially premixed combustion air prior to combustion such a way that the combustion of part of the air mixed in advance with the gas (primary air excess coefficient between 0.2-0.8), followed by combustion. The advantage is clear combustion flame, combustion strengthened, high thermal efficiency. However, combustion instability, and high combustible component of the control primary air requirements. The gas burner usually used such combustion. 3, i.e. flameless combustion air which has been uniformly mixed with the combustion gas prior to such gas required for combustion. Primary excess air ratio is equal to the excess air ratio for complete combustion of the fuel required to obtain oxygen from the ambient air during the combustion process. When the combustion gas and air mixture reaches the combustion zone can be completed in an instant.
1 type: SZS D type Horizontal firetube steam boiler agua quente a
WNS oil gas fired horizontal steam boiler