The method is properly installed steam boiler when we sent you receive your steam boiler, you must be very happy, but at the same time, certainly some questions. Fuel gas boiler is not only fuel but also refers to the gas boiler. Previously no such dual-fuel boiler, burner because either fuel or gas, no dual fuel burners. With the rapid development of the world energy equipment, some European countries begin production and sales of fuel gas burner, dual fuel burner and boiler combination of organic birth of a new breed of boiler - fuel gas-fired boiler. Electric heating boiler and the boiler is mainly composed of electric control box and control system. Its characteristics are environmentally friendly, clean, no pollution, no noise, automatic, with limited energy and reduce prices significantly, as a new boiler electric heating boiler equipment increasingly being recognized. Electric heating the core member is electrically heated boiler, directly determines the life of the boiler, to select a non-metallic electrical heating tube (such as a ceramic heating pipe), because it is resistant to the load, a long life, and a water separation structure, the boiler Wing no leakage. How to install steam boilers correct? Do not worry. We Eastern Machinery not only produce high quality boiler, but also have high-quality after-sales service. We teach you how to properly install. First, in order to investigate the installation environment, boiler room layout should prior approval of the local quality and technical monitoring section, and install a separate boiler room installed in ventilation, cooling, easy to operate and convenient place to smoke. Not near flammable or explosive material, electrical installation technicians should be installed in accordance with the requirements of the relevant national standards, and N and L error can not be connected. When using gas as fuel, explosion-proof electrical equipment should be installed, from the switchboard should 6m above the pan. Secondly, the ground electric steam boilers relation to the safe use of the boiler. For this reason, reliable ground should be installed, should be stored in the vicinity of the ground, the depth should be greater than or equal to 1.5 m, the ground should be sintered at a cable joint ground pile head. In order to prevent corrosion and moisture, the connection joint should preferably 100mm above the ground. Boiler chimney to be discharged should be extended to the outside, the outlet should be 1.5 to 2 meters higher than the boiler. After installation, the local special equipment maintenance department should be declared. The relevant part of the experience received consent to use, and has made use of certificates boiler before use. Volume is less than the vapor pressure of less than 0.1L or 30L fired steam generator factory price belonging to the National Inspection-free range, that is, without the use of a certificate issued by the boiler can be used. Follow the steps editorial suggestions, I believe you will be able to successfully install a steam boiler!
Works steam boiler steam boiler structural characteristics: 1. Heat generated in combustion of coal is first absorbed water wall heat transfer by radiation, boiling off the water wall, a large amount of steam (excluding DC furnace) inside the drum, separated saturated steam enters the superheater, and by radiation and convection manner continue to absorb top horizontal flue heat and smoke flue tail, the superheated steam to reach the required operating temperature. Steam boilers for power generation is usually provided with a reheater, to a high pressure steam heated cylinders. Reheat steam reheaters into the low-pressure cylinder continue to work to generate electricity. 2. pulverized coal work, the location of the center of the flame will affect evaporation. Generally, when the center of the flame is low, a large amount of evaporation, and when the high center of the flame, a small amount of evaporation. Also affects the position of the center of the flame superheated steam or reheat steam temperature. Normally, when the center of the flame is low, superheated steam, in particular steam reheating temperature to be low, and the temperature of the superheated steam is high. 3. Pulverized Coal Burner front and rear walls is arranged a thrust manner, tangential firing mode, bis tangential firing methods, each method has its own characteristics. Biomass boiler is a kind of boiler to biomass energy as a boiler fuel called biomass boilers, steam boilers into biomass, biomass hot water boiler, biomass stove, biomass thermal oil heaters, vertical raw biomass boilers, biomass boilers and other horizontal. Since the above-described arrangement can not be applied in the same furnace at the same time, the influence of steam can not be directly determined. Steam boiler structural characteristics: 1, the steam boiler body welding: the main welding using submerged arc welding technology advanced, to ensure the welding quality. There are heating and hot water boiler bath for two purposes. Hot water boiler by circulating hot water circulation pump hot water holding tank, the tank hot water heating cycle can be achieved bath object; hot water boiler by circulating hot water circulation pump heating conduit, through the heat sink (radiator) people can achieve heating requirements; hot water boiler and hot water circulating pump with heat exchanger can be achieved bathing and heating dual function. All welds are main as required "safety Technology supervision standard", 100% ray detection electrode according to the eligibility criteria Ⅱ. 2 is a horizontal steam boiler combustion all wet back three-loop structure. 3. The steam boiler front smoke box is sealed asbestos refractory material made of graphite. The reliable seal, ensures that no leakage of steam boiler flue gas at positive pressure conditions. 4. Thread flue: fired steam generator factory price secondary regenerator flue threaded convection heating surface, contribute to the efficient heat transfer. Enhanced heat transfer, thermal efficiency of the steam boiler, a single light pipe threaded pipe or 2.4. When the fluid flows in the tube, the flow rate of the fluid near the wall is low, the fluid on the wall boundary layer is called. In several of the flue gas duct in the outer aqueous series resistance, the maximum thermal boundary layer, but the boundary layer is very thin, as long as the boundary layer is slightly perturbed, such as by pressing on a common wall of the boss, the thermal resistance will be greatly reduced, while an effective method which is threaded pipe. 5. To make the system more energy efficient, using a continuously adjustable water supply, avoiding frequent start the pump. Between the second and the third pivot smoke tubes have a broad space for water, in order to ensure natural circulation of water in the pot.
In particular reactor is often used to complete the production process of curing material, hydrogenation, alkylation, polymerization and condensation process. Reactor for heating, cooling and gas absorption and liquid extraction processes require a physical change to using the apparatus to obtain a good stirring effect. Chemical plant reactor inseparable, many chemical plants in order to save costs, the reaction vessel of the production system to the original electric heating fired steam generator factory price heating steam, nearly million annual cost savings, cost reduction for the company by Adds new efficiency initiatives.
To accelerate the low nitrogen transformation gas boiler in each area of Xian, October 23, 2018, liberation of the door street in charge of leading Korean right lead a public person with low nitrogen regional transformation slow the unit door butt again, and supervise the various units to speed up progress, by the time limit to complete the task of transformation.
1, Imperial Square area, parking building, Suntech Lane three projects reflect seven plots site inspections carried out two times, road construction site clean and moist, well-covered, site supervision and regular opening spraying dust and other facilities, strict implementation of air pollution control measures.
2, the region west of Seven Road, Sheung Tak Road, west along the eight dining pollution checks to ensure that all food and beverage outlets normal use of fume purification facilities, and urge all stores on a regular basis to do routine maintenance.