Check Item item hot water boiler hot water boiler comprising a boiler inspection and checking internal use preparations, checking in the furnace and the flue, the boiler attachment check, check automatic control system, the secondary device, check the combustion device, the auxiliary heat check the surface of the hot water boiler must be done before running some tests, these tests are quite a lot of us, it is possible because of our neglect and causing very serious consequences. Therefore, we must forestall, be sure to carefully check the following before the hot water boiler operation. 1, including the use of internal inspection and boiler ready. 2, inspection, and furnace fouling and debris inside the flue in the furnace and flue should be cleaned. Flue duct and damper, the shutter must be complete and compact, flexible switch, opening and closing accurately indicated. 3, check the boiler accessories, check the safety accessory is intact; cock is rotating flexible, easy to use; all kinds of instruments and controls should be complete, good, clean. After passing the examination, should the gauge cocks in working condition. 4, check the automatic control system. 5. Check the accessory device. 6, inspection of the combustion apparatus, the combustion apparatus is intact inspection; mechanical transmission system, coal handling system, the ballast system test switch normally; spring-loaded safety level of a gearbox should be appropriate, well lubricated; coal shutter indicate the correct scale. iron eagle neat, well, turn the ballast plates full, flexible movement. 7, the auxiliary heating surface of the inspection, check the auxiliary device (fan, blower, pump, etc.) are firmly connected coupling; proper belt tension triangle; oil should be good enough; cooling water flow. After passing the examination, installed security guard, respectively, commissioning, and note the current when idling. It is fed out of the hot water boiler heat equivalent to a mass per hour (usually expressed in tons) in water was heated from 20 ℃ and heat output of all vaporized into a steam boiler made in korea packaged coal boiler water absorbed three expressions, in tons) water from 20 ℃ heated and vaporized into all heat absorbed by the steam boiler it is fed out of the hot water heat equivalent to a mass per hour (i.e. typically kcal / hr (kcal / h), tonnes / hour (t / h ), megawatt (MW). (1) kcal / h is in metric units of expression, which represents the heat of hot water boiler fed out per hour. (2) t t borrowed steamed steam boiler popular argument, ( 3) megawatts (MW) is the international system of units unit of power, the basic unit is W (1MW = 106W). this expression formal documents should be used.
Distinction gas steam boiler made in korea packaged coal boiler and a conventional coal-fired boilers and gas steam boiler (1) in a conventional coal fired boiler should be prechamber through grinding equipment, coal should be produced for combustion injected into the furnace, the entire combustion process in furnace and in the form of a suspension. (2) as long as the gas steam boiler biomass fuels open, dried and crushed, the helical feeder to the air before it is blown into the top of the combustion grate vibration. After burning the soot removed from the baghouse gas steam boiler. 2, different air supply preheating. Gas-fired steam boiler burner underlying mode, two-pass configuration, the fuel combustion, the boiler operation is stable and take up less space, while the spoiler is inserted smoke tube, smoke slow speed, increase heat transfer, a high thermal efficiency, reducing user fees (1) coal-fired boiler air preheater flue at the bottom, below the economizer; using flue (2) temperature of the air supply end of the cigarette is heated, different from a conventional boiler, the feed gas steam boiler air preheated by the air preheater flue gas cooler and the two parts to feed water as a medium to absorb heat of the flue gas, conveying air into the furnace. Warm air supply system for a gas steam boiler is controlled by adjusting the supply air temperature of the heating water flow can be provided by adjusting the electric charge of the bypass track circulation water through the valve and the air preheater flue gas cooler bypass control. Water heat exchange section, cooling water heated through the air preheater and the cold air delivery fan; then, this part of the water continues to flue gas cooler, flue gas by exchanging heat with water in the flue gas cooler, water heating, cooling the flue gas. In the bypass, a bypass flue gas cooler and another bypass air preheater, both have their own electrical control bypass and isolation valves. When the flue gas cooler exit gas temperature is too low, the bypass isolation valve is opened, water does not pass through the flue gas cooler, flue gas heat exchanger is not performed to ensure the flue gas cooler outlet gas temperature is not too low smoke corrode gas cooler. In order to enter the flue gas cooler feedwater temperature is not too low, when the air preheater outlet water temperature is below a certain temperature, it opens the bypass, supply cool air can not be heated, the water temperature is too low to prevent the influence of the flue gas cooler work . But also to ensure the temperature of the flue gas through a gas steam boiler precipitator. 3. The coal-fired boiler flue gas fired boiler bag filter should be used for desulfurization libraries to ensure the emission of pollutants lower than the standard. Steam boiler is an energy conversion device, the energy input to the boiler fuel chemical energy, electrical energy, thermal energy and other forms of high temperature flue gas, and after converting the boiler, the steam output having a certain outside thermal energy, high-temperature hot water or an organic carrier. Gas hot water boiler with environmental protection, energy conservation, safety, salient features fully automatic operation, and ease of use. In addition, due to the operation of the economy, government policies to encourage, gas hot water boiler more and more people of all ages. However, biomass combustion flue gas are different. Biomass fuel of low sulfur and nitrogen content, only through the biomass filter before discharge into the atmosphere. However, the carbon content of fly ash produced by the combustion of biomass, coal-fired boiler boiler efficiency is better, but the carbon dioxide content in the greenhouse can be reduced. Under the same nitrogen content of the fuel, the nitrogen oxides emission concentration of boiler far below the emission standards for coal-fired boilers. The problem should be noted that operation of the gas boiler. From the operational perspective view of the gas boiler, the operation of the gas boiler should note the following: The actual fuel consumption of the boiler operation, the amount of oil to the adjustment screw feeder. Unburnt fuel in the furnace, induced draft fan and the blower can not be stopped. Sudden power outage in operation, must be promptly removed fuel furnace. Not add biomass fuel before the shutdown. When the furnace stopped, there is no need of the bank up a fire. When the fuel on the grate exhausted, drum induced draft fan may stop running. If you want to know more about boiler, gas steam boiler, you can log on to our website, we look forward to your call!
Mixed biomass and coal fired steam boiler made in korea packaged coal boiler, what the hell it is? Literally, you can guess is that a kind of steam boiler which can burning biomass fuel and coal fuel at the same time. Bingo, you are right here. In ZG Boiler, our engineer can reform some old chain gate boilers on technology parts. As to national policy, governments encourage factories use biomass fuel, natural gas, etc those clean energy during their producing or manufacturing process. Here, according to the rich experience on boiler reforming, our ZG Boiler put new type mixed biomass and coal fired steam boiler into markets. This mixed biomass and coal fired steam boiler, is also a kind of chain grate boiler, DZL and SZL to choose for different consumers.
Fangkuai Boiler has carried out a large-scale welding revolution, eliminating traditional manual welding operations with low efficiency, low accuracy and poor stability, and converted it to the use of mechanical welding equipment with high efficiency, high accuracy and high stability for automatic operation . Realize welding automation of all important parts from the drum to the tube sheet. The submerged arc welding, argon arc welding, carbon dioxide welding and other welding details of the process have also made corresponding intelligent changes, workers' welding environment is cleaner, and the quality of boiler welds is more guaranteed.