Tel No. (+86) 371-55629010

150 Psi Coal Steam Boiler

Several factors underlie the vertical 150 psi coal steam boiler efficiency China has been working to catch on coal to natural gas, vertical steam boiler with greatly reduced contamination of dust, smoke and other effects of a nitric oxide gas has also been healthy curb. Efficiency is an important indicator of a measure of vertical steam boiler, a good number of factors under the topic to discuss the direct impact of vertical steam boiler efficiency began. After analysis of stakeholders, heat loss from vertical steam boiler contains two pieces: the proportion of full combustion air with flue gas emissions unreasonable heat loss. Heat loss can be reduced smoke emission can be installed at the end of the vertical steam boiler stack waste heat reuse install, or more leading system with condensing boiler. Combustion air ratio sufficient unreasonable faults into: general vertical ejector-type steam boiler burner selection, resulting in a motor fuel ratio can not be adjusted. Most of the selected vertical steam boiler is mechanically strong emission combustion engine, air-fuel ratio resulting irrational factors are the following: air-fuel ratio can be divided into two reasonable chance comprising: when the air in excess, the excess will have full cold It is heated, resulting in increased operating costs vertical steam boiler, steam boiler efficiency vertical drop; when the air is not enough, will produce insufficient burning phenomenon, caused by vertical steam boiler efficiency.

Recently, the party's fast Heli De H2800 boiler successful Jingdong headquarters procurement project. He Lide H2800 party fast adoption of new environmental protection industry leading combustion technology - premix combustion, fuel and air through precise regulation and control to achieve precise ratio, can ensure complete mixing of gas and air, burning more fully. The new technique Ultraten heat exchange elements - wings pipe, is a unique fast side. A unique built-tearing groove design, compared with ordinary heat transfer tubes, the heat transfer area can be increased 5-fold, greatly enhance the heat transfer rate, to strengthen the central flue of the disturbance, so that heat transfer efficiency is better, more energy efficiency .

The main characteristics of the indicators boiler What? To demonstrate configuration, capacity, parameter and economical operation of the boiler, etc., generally represented by the following indicators to the basic characteristics of the boiler. A) evaporation industrial boilers evaporation is generally 0.1 ~ 65t / h. For the hot water boiler with a nominal thermal power of its capacity to indicate the size, in units of MW. (Ii) pressure and temperature for saturated steam production boiler, just indicate steam pressure. For the production of superheated 150 psi coal steam boiler, the steam temperature of the steam must be marked at the outlet of the superheater, i.e., superheated steam temperature, the unit is deg.] C. For hot water boiler, the hot water temperature has rated outlet and rated the import of sub backwater temperature. With rated thermal power, rated water temperature and the return temperature corresponding to the rated nominal referred circulating water flow of water through the hot water boiler, the unit is t / h. Heating boiler (iii) an evaporator heating surface and the heating surface of the heat generation rate surface evaporation rate or heating rate is an indicator of the intensity of the boiler work, the greater the numerical value, the better the heat transfer, the smaller the amount of metal consumed boiler. Heating surface evaporation rate general industrial boiler is less than 40kg / (m · h); heating surface of the heating rate of hot water boiler is less than 83700kJ / (m · h) iv) the thermal efficiency of the boiler which is an index indicating economical boiler heat, general industrial combustion thermal coal boiler efficiency of around 60% to 82%. Sometimes, in order to measure the heat economy schematically steam boiler, are also commonly used coal or coal water vapor than the ratio expressed as the ratio of the amount of coal in the boiler per unit time over the period of time and the amount of steam production. Coal-water ratio of about the size and type of boiler, coal quality and operation management quality and other factors. Industrial boilers coal-water ratio is generally l: 6 ~ 1: 7.5. Description (a) Evaporation: desired amount of steam produced per hour steam boiler called evaporation, the unit is t / h steam boiler showed that the size of the rated capacity of evaporation, i.e. in boiler design parameters and ensure a certain efficiency. maximum continuous evaporation, also known as the rated output of the boiler (ii) pressure and temperature: the rated pressure steam boiler of the steam at the outlet of the steam or the hot water boiler rated working pressure rated pressure at the outlet of the hot water boiler is called, and He said maximum working pressure, in units of MPa (iii) an evaporator heating surface and the heating surface of the heat generation rate: refers to the heating surface of the pot soft drinks and other heat transfer medium and the flue gas heat exchange area of ​​the pressure receiving member, usually with smoke metal surface area of ​​the gas-side heating area is calculated, in units of square meters. the amount of steam per hour per square meter of the resulting heating surface, called boiler heating surface evaporation rate, in units of kg / (m · h) per hour hot water boiler m² heating surface of heat generated by the heat generation rate is referred to as heating surface, the unit is kJ / (m · h). (Iv) thermal efficiency: thermal efficiency of the boiler is a boiler effective utilization percentage of the heat input and heat boiler per unit time, also called boiler efficiency, [eta] is represented by the symbol.

Reducing the project covers an area large 150 psi coal steam boiler and therefore a large high-pressure steam boiler pipe insulation manufacturers buried heating pipe does not require masonry huge trench, just insulation pipe buried underground people, thus greatly reducing the project area, reducing earthwork open dig about 50% or more, reducing the amount of civil masonry and concrete 90%. Gas boiler, pipe insulation and processed in parallel trenching site, linker site only, shorten the construction period can be greater than about 50%, thermokeeping pipe is widely used a liquid, a gas pipeline network, Chemical Engineering Oil pipe insulation, the vapor Hence largest chemical boiler, central heating network, air conditioning and ventilation ducts, municipal engineering. Buried pipe insulation is one kind of good insulation properties, plus safe, reliable, low construction cost of the prefabricated buried pipe insulation. Effective solution incubated urban centralized heating with a high temperature heat input thermokeeping tube, sliding and water lubrication problems exposed tube ends. Buried pipe insulation not only has the traditional trench laying of pipelines and overhead incomparable advanced technology, practical performance, but also has significant social and economic benefits, but also energy-saving heating of effective measures. Prefabricated buried pipe insulation technology using buried heating pipe, marking polyurethane insulation heating pipe technology development has entered a new starting point. Reporters noted that this year again Yajian steel production capacity of about 50 million tons, quit more than 150 million tons of coal production capacity. Even the industry is expected this year to production capacity will be extended to glass, construction accounted for a large reduction in the steam boiler electrolytic aluminum, cement and shipbuilding industries. High pressure steam boiler pipe insulation manufacturers of polyurethane buried insulating pipe evacuated provided.